milimission.blogg.se

Hikvision ip camera utility
Hikvision ip camera utility




hikvision ip camera utility
  1. #Hikvision ip camera utility software#
  2. #Hikvision ip camera utility Pc#
  3. #Hikvision ip camera utility Offline#
  4. #Hikvision ip camera utility mac#

Now for the most part with the UPPER models of Hikvision UPS, they have dual boot partition somewhere in their NVRAM so they can take a little bit of ungraceful shutdowns eventually. Of course when power returns it turns on. Eventually the UPS goes down and so does the NVR but in this case not gracefully.

hikvision ip camera utility

if the UPS has only 5 minutes of POwer left it will send a shutdown string bu tthe NVR will not recognize it.

#Hikvision ip camera utility Pc#

So when the power returns and the UPS is charged the PC goes on. I can in the BIOS se the PC to turn on once there is power. it stops processes and gracefully shuts off.

hikvision ip camera utility

THE UPS battery has only 5 minutes of capacity left, UPS sends a shutdown signal to the Win or Linux PC. Thought experiment: A window or Linux machine is hooked to the UPS. I would want the UPS to shut down gracefully the NVR when there is not enogh battery capacity. Usually if its something bad with the recorder, it will happen often and frequently. If it happens like once every 2 months, that will be a tough one, more than likely something on your network causing the issue. possible bad NVR? How often does this happen? is it every day? If so, that can be an easily duplicatated issue and should be warranted by your dealer. It may even be worthwhile to change all of the port numbers to something completely different. And rebooting the NVR would reset all the UPNP rules which would cause it to work again. Given your symptoms, I almost think this could be the case, because you said emails still work which means outgoing traffic is still working, and it still responds to pings, but accessing the web page is intermittent. Turn off UPNP on all your cameras and NVR, If you have already done port forwarding, but you still have UPNP on your NVR, then you have a port conflict which causes all kinds of issues including the one you mentioned. Possible IP conflict? Rare yes, but if you have your IP address set low to what most of your other devices are set to, then you increase the likelihood of a conflict when another device comes on the network via DHCP (such as a cellphone, computer, etc) Set your IP address really high, I usually do mine in the 240 and up range. That should not be happening and is not really normal. I think the real problem that should be tackled is why is your NVR not responding to requests when trying to access the web interface. I know of no tool from Hik that allows remote rebooting.

hikvision ip camera utility

In this case, the recommendation would be to set a static IP address for one of them.Interesting.

#Hikvision ip camera utility Offline#

Neither will be able to connect to the network and cameras may randomly go offline or not stream video to a recorder. If two cameras share the same address, errors will typically not be generated. What if more than one device attempts to use the same IP address? It can be found in the Physical Address column.

#Hikvision ip camera utility mac#

Your camera will be displayed in the "arp table" and will be identified through its MAC address. This list contains the IP addresses, MAC addresses and allocation type (whether static or dynamic) for all available hosts. Connect your IP camera to the router through the physical cable

#Hikvision ip camera utility software#

IP Helper Software can be downloaded from the following links and be installed on your Mobile device or Laptop:ġ. It is used for discovering devices and basic network configuration and licensing IP Helper is a generic discovery and network-configuration tool for all Bosch IP Network Video Products. Search for the camera IP using its MAC address: Under My Devicestab > press Network scanģ. Here we will introduce 3 ways to find the network camera IP address quickly and easily.Ģ. The steps below assume you already have the MAC address of your camera installed and connected to a router with Internet access.Ĭameras need physical network cable connection for the initial setup in order to get the IP camera address while connected to the router. Like any network device, the camera is assigned an IP address when it is connected to the router with Internet access and powered on. The IP camera address is always the key if you would like to monitor or remote viewing it.






Hikvision ip camera utility